|
| MBD-X9DRi-F -O | - X9DRi-F (Standard Retail Pack)
| | MBD-X9DRi-F -B | |
| | |
| Form Factor | | | Dimensions | - 12" x 13" (30.5cm x 33.2cm)
|
| | |
| CPU | - Intel® Xeon® processor E5-2600 (up to 135W TDP **)
- Dual Socket R (LGA 2011)
| | Cache | | | System Bus | | | | ** Motherboard supports this maximum TDP. Please verify your system can thermally support. |
| | |
| Memory Capacity | - 16x 240-pin DDR3 DIMM sockets
- Supports up to 512 GB DDR3 ECC Registered memory (RDIMM)
- Supports up to 128 GB DDR3 ECC/non-ECC Un-Buffered memory (UDIMM)
| | Memory Type | - 1600/1333/1066/800MHz ECC DDR3 SDRAM 72-bit, 240-pin gold-plated DIMMs
- Support ECC and non-ECC UDIMMs
| | DIMM Sizes | - 32GB, 16GB, 8GB, 4GB, 2GB, 1GB
| | Memory Voltage | | | Error Detection | - Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| | |
| Chipset | | | AHCI SATA | - SATA 2.0 3Gbps with RAID 0, 1, 5, 10
SATA 3.0 6Gbps with RAID 0, 1, 5, 10
| | SCU SATA (Storage Controller) | - SATA 2.0 3Gbps with RAID 0, 1, 10
| | IPMI | - Support for Intelligent Platform Management Interface v.2.0
- IPMI 2.0 with virtual media over LAN and KVM-over-LAN support
- Nuvoton WPCM450 BMC
| | Network Controllers | - Intel® i350 Dual Port Gigabit Ethernet
- Virtual Machine Device Queues reduce I/O overhead
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45 output
- 1x Realtek RTL8201N PHY (dedicated IPMI)
| | Video | |
| | |
| AHCI SATA | - 2 SATA 3.0 ports (6Gbps)
- 4 SATA 2.0 ports (3Gbps)
| | SCU SATA | | | LAN | - 2 RJ45 Gigabit Ethernet LAN ports
- 1 RJ45 Dedicated IPMI LAN port
| | USB | - 11 USB 2.0 ports total
(4 rear + 6 via header + 1 Type A)
| | Video | | | Serial Port / Header | - 2 Fast UART 16550 ports: 1 rear and 1 header
| | DOM | - 1 DOM (Disk on Module) power connector
| | TPM | |
| | |
| 2U Chassis | | | 3U Chassis | | | Tower / 4U Rackmount | | | Important Chassis Notes | - To support the new generation Intel® Xeon® processor-based motherboards, Revision M chassis is recommended. Please talk to your sales representative for details.
- Please use optional I/O shield MCP-260-00041-0N in Supermicro 1U chassis
|
| | |
| PCI-Express | - 3x PCI-E 3.0 x16 slots
- 3x PCI-E 3.0 x8 slots
(Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. See manual block diagram for details.)
|
| | |
| BIOS Type | - 128Mb SPI Flash EEPROM with AMI BIOS
| | BIOS Features | - Plug and Play (PnP)
- APM 1.2
- PCI 2.3
- ACPI 1.0 / 2.0 / 3.0 / 4.0
- USB Keyboard support
- SMBIOS 2.7.1
- UEFI
|
| | |
| Software | - IPMI (Intelligent Platform Management Interface) v1.5 / 2.0 with KVM support
- SuperDoctor® III
- Watch Dog
- NMI
- Optional IPMI 1.5 / 2.0
| | Power Configurations | - ACPI / APM Power Management
- Main Switch Override Mechanism
- CPU Fan auto-off in sleep mode
- Power-on mode for AC power recovery
|
| | |
| Voltage | - Monitors for CPU Cores, +1.1V, +1.5V, +3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, 4 Memory Voltages.
- 5+1 Phase-switching voltage regulator
| | FAN | - 8x 4-pin fan headers (up to 8 fans)
- 8x fans with tachometer monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Pulse Width Modulated (PWM) fan connectors
| | Temperature | - Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x Fan Connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- PECI
| | LED | - CPU / System Overheat LED
| | Other Features | - Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
|
| | |
| Operating Temperature Range | - 10°C - 35°C (50°F - 95°F)
| | Non-Operating Temperature Range | - -40°C - 70°C (-40°F - 158°F)
| | Operating Relative Humidity Range | - 8% - 90% (non-condensing)
| | Non-Operating Relative Humidity Range | - 5% - 95% (non-condensing)
|
|
